Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterGenie Garage Door Installation in Denton: What to Know First
We install Genie garage doors in Denton with a flat, written price and scope before any work begins. Typical turnaround on a standard single-door replacement is one visit, usually 3 to 5 hours on site, with full new door installation in Denton running $700 to $2,200 depending on size, material, and what the opening requires. You’ll see the exact number before we touch a bolt, because that’s Clause 1 of The Haven Standard and we don’t work any other way.
This page is for homeowners who own a Genie product or are considering one, and need the door itself installed or replaced, not just the opener. If you’re in Denton and you’ve been researching before calling anyone, you’re our kind of customer. Call (940) 398-6880 and a live person answers, 24/7. Not a callback window.
How Genie Products Fail - and How We Fix Them
Genie has made residential garage door openers and related components for decades, and certain failure modes show up in Denton homes more than others. Here’s what we actually see on service calls, and what we do about it.
- Genie screw-drive rail wear on older 1022 and 2022 models. The screw-drive rail on those units was a sturdy design, but after 10 to 15 years of Denton heat cycling, the grease thins and the carriage begins to chatter. The symptom is a door that jerks halfway up. The fix isn’t the door; it’s replacing the rail assembly or moving to a belt-drive Genie unit, which we can install same visit if you want the upgrade.
- Intellicode receiver drift on Genie AC-powered models. When a Genie opener stops responding to remotes but the wall button still works, the receiver board has usually drifted off frequency. This is a known Genie characteristic, not a remote battery issue. We can replace the logic board or, if the opener is old enough that the board costs more than half a new unit, we’ll tell you that too and show you the part price before you decide.
- Tension spring mismatch on Genie Excelerator doors. The Genie Excelerator series uses a counterbalance spring spec that doesn’t always match what a previous installer put on. We see this in Denton homes where a handyman replaced a spring with whatever was on the truck. The door hangs heavy, the opener motor burns out early, and the owner blames the opener. We measure the door weight and check spring torque before judging the motor.
- Photo-eye alignment on Genie Safe-T-Beam systems. Genie’s Safe-T-Beam sensors are sometimes positioned too close to the track edge, so wind or door vibration breaks the beam and the door reverses for no reason the owner can see. This is especially common after a new door installation when the track got nudged. We realign the sensors and check the mount depth; most of the time that’s the entire repair.
- Wall console wiring on Genie Series II openers. The Series II consoles use thin gauge wire that corrodes at the terminal block in humid Denton summers. The door opens from the car remote but not the wall button. We replace the console wire and the terminals, and we photograph the corrosion before we quote the fix so you’re not taking our word for it.
Our Genie Garage Door Installation Process
- 1
You call, we answer. A live person picks up at (940) 398-6880. We ask what you’re seeing, what the door is doing, and whether it’s a Genie door, opener, or both.
- 2
We schedule and show up. The technician arrives in a Servo truck, uniformed and background-checked. You’ll get the name before arrival and an on-the-way text.
- 3
We measure and document. The tech checks door weight, spring torque, track condition, and the opener. Every failed component gets photographed before any quote. That’s Clause 4 of The Haven Standard, and it’s non-negotiable.
- 4
You get a flat written price. The scope is written, the price is written, and it doesn’t change after we start. If the job needs something extra, that gets written and agreed before that extra happens.
- 5
We do the work. New door, opener, springs, track, whatever the scope says. We use Genie OEM parts when it matters for warranty, and quality aftermarket only when it’s the better dollar decision and we tell you why.
- 6
We test and you see the proof. The door cycles a full open and close with the balance checked, photo-eye tested, and the opener travel limits set. You get a documented photo record of what we found and what we did, plus the warranty in writing, before we leave.
BeforeAfterWhat Genie Garage Door Installation Costs in Denton
New door installation in Denton runs $700 to $2,200 complete, depending on door size, gauge of steel, insulation, and whether it’s a single or double car opening. A single steel door in the $700 to $1,200 range is our most common Denton install. A double-car insulated door with a Genie opener runs $1,600 to $2,200. If your existing opener is still sound, you don’t pay for a new one. If it’s a 15-year-old Genie screw-drive that’s already struggling, we’ll tell you what a replacement costs and you decide.
Here’s the range set we quote from on Genie-related work in Denton:
- Single car door installation: $700-$1,200
- Double car door installation: $1,100-$2,200
- Genie opener installation (door already in place): $250-$550
- Spring replacement on a Genie-installed door: $180-$340
- Panel replacement for a damaged Genie door section: $250-$500
What moves the price: door size, insulation level, steel gauge, and whether the existing track and springs are compatible or need replacement along with the door. You’ll know the exact number before any work starts. Estimates are free, and there is no such thing as a quote that changes after we start.
Why Denton Homeowners Call Servo Garage Doors Denton for Genie Work
We’re an independent Genie service provider, not a manufacturer arm and not a franchise. That independence means we call it like it is: if a Genie opener is worth repairing, we repair it. If the logic board costs more than the unit is worth, we show you both numbers and let you decide with the paperwork in front of you. Marcus Deller, our owner, will quote a firm price range before a single bolt turns, and every technician on the truck works the same way.
The 365-Day Done Right Promise is in writing, not in a handshake. If a repair isn’t right, we make it right. No one has to ask twice. And because we service all major brands including LiftMaster, Chamberlain, and six others, when a Genie repair isn’t the right call, we’re not forcing you into a brand you didn’t ask for. We’ll fix what you have or quote what works.
The multi-brand part matters. Some Denton homes have a Genie opener from one owner and a LiftMaster from another. We work on both.
FAQs
Yes, in almost every case the opener can be replaced independently of the door. We check the door balance and spring condition first, because an unbalanced door will burn out even a brand new Genie opener within a year. If the springs need replacement, you’ll see that on the written scope before we install anything. Call (940) 398-6880 and we’ll schedule a check.
We use Genie OEM parts whenever the repair involves warranty-covered components like the motor, logic board, or rail. For general hardware like rollers, hinges, and sensors, we use quality aftermarket parts when they match or exceed the Genie spec and cost less. The choice is shown to you line by line before any work begins.
Most standard single-door replacements are done in one visit, typically scheduled within a few days of your call. We don’t promise same-day on installations because the door is measured and ordered, not picked off a shelf. What we promise is a written schedule and a flat price before the door is ordered. If your situation is urgent, call and we’ll get you a clear answer.
No. The price you get in writing before we start is the price you pay. That’s Clause 1 of The Haven Standard. If the job reveals something outside the original scope, like a rotted header or a track that must be replaced, we write a separate scope and you agree to it before that extra work happens. No surprises when the invoice comes.
Yes. If any part of the installation isn’t right within 365 days, we make it right. No deductibles, no re-inspection fees, no forms. You call, we come back, we fix it. That applies to new door installation and opener installation alike. Call (940) 398-6880 for a free estimate.
Written by Marcus Deller, Owner, Servo Garage Doors Denton at Servo Garage Doors Denton, serving Denton and nearby areas.